All products

%
Nabertherm LVT 9/11/C550 ashing furnace
Ashing furnace LV(T) .. 11 is designed especially for ashing processes to 1050 °C in the laboratory. Applications include determining loss on ignition, ashing food and plastics for subsequent substance analysis. A special fresh-air and exhaust air system ensures that the air is replaced 6 times per minute so that there is always sufficient oxygen for the ashing process. Incoming air passes the furnace heating and is pre-heated to ensure good temperature uniformity.

Standard Equipment
• Heating from two sides
• Ceramic heating plates with integral heating element which is safeguarded, and easy to replace
• Air exchange of more than 6 times per minute
• Good temperature uniformity due to preheating of incoming air, temperature uniformity according to DIN 17052-1 to +/− 10 °C in the defined empty work area (from 550 °C)
• Dual shell housing made of textured stainless steel sheets with additional fan cooling for low surface temperature
• Exclusive use of insulation materials without categorization according to EC Regulation No. 1272/2008 (CLP)
• Suitable for many standardized ashing processes according to ISO, ASTM, EN, and DIN
• With lift door (LVT)
• Solid state relays provide for lownoise operation
• Controller C550 (10 programs with each 20 segments)

Option
• Over-temperature limiter with adjustable cutout temperature as temperature limiter to protect the furnace and load
• Port for thermocouple in the rear wall or in the furnace door
%
Kühner EPFL table 5 clamps (Z)
This table accepts up to five tube holders, each with a capacity of 24 x 50ml tubes. Each tube holder has its own clamp handle allowing it to be easily taken out of the incubator shaker and put on a clean bench while the other tubes keep on shaking. It’s also possible to shake microtiter plates on the EPFL-table, using Duetz 4-place coverclamps. If you have a Kuhner F-size tray (800 x 420mm), you can also clamp that on the table instead of individual holders.
%
Kühner Test tube holder RGH-32 (14 tubes)
• Test tube holder RGH-32 (14 tubes)
• For 14 test tubes with 32 - 33 mm diameter
%
Kühner Clamp U-200
Clamp U-200 for Erlenmeyer flasks with 200 ml vol.
%
Kühner Tray with fixed clamps E-1000
Tray with fixed clamps E-1000 To load 9 Erlenmeyer flasks with a volume of 1000 ml
%
Stakpure RT 500 PP + sloped bottom
Storage tanks in grey PP with sloping tank bottom for storing purified water from reverse osmosis systems. Closed and opaque design, round, including manhole for cleaning. The tank comes completely piped and is available with optional accessories.
• Input connection: R ¾''
• Drain connection: R 1¼''
• Volume (l): 500
• Dimensions (Ø x height, mm): 780 x 1100
• Net weight (kg): 20
%
Stakpure Ion excahnge cartridge DS 6000 without resin
Up to 10 bar pressure-resistant, stainless steel, empty cartridge for ion exchange resin.
• Material: stainless steel – AISI 316
• Dimensions mm (Ø x height): 240 x 1155
• Connection: R ¾ "
%
Nabertherm collecting Pan, Steel for L..5
• Tmax 1100 °C
• Dimensions 190 x 170 x 20 mm
• For models LE 4, LE 6, L 5, LT 5, LV 5, LVT 5
%
Esco Ice Scraper
Ice scraper is available for cleaning ice built up on door gasket, PEP and other places in the freezer.
%
Ohaus Rotor, Angle, 6x250ml FB, ID
Frontier rotors extend the functionality of Frontier centrifuges by increasing the number of tubes of varied types and sizes that can be used in conjunction with each of the centrifuge models. Easy to clean and operate, the rotors are durably constructed to withstand demanding centrifugation.

Compatible adapters and other accessories:
• Adapter, 1x50ml D29mm RB, 2/pk (30304373); Adapter, 1x50ml D30mm FA, 2/pk (30304374); Adapter, 2x30ml D26mm RB, 2/pk (30304372); Adapter, 4x15ml D17mm FA, 2/pk (30304371); Adapter, 5x10ml D16mm RB, 2/pk (30304370); Adapter, 8x1.5ml D11mm, 2/pk (30304369)
%
Miele APLW 010 upper basket
Upper basket with 156 unoccupied injector slots for nozzles with Ø 2.5 mm.
• Area of application: reprocessing laboratory glassware
• Only suitable for use on upper levels

Machine affiliation: Can be used for PLW 6111 devices.
%
Ohaus PX6202 precision balance
The Pioneer PX combines essential weighing functionality with competitive performance, offering high accuracy and repeatability for applications in laboratory, industrial and education settings. The PX is affordably priced, and intuitively designed for intelligent operation with a second line display for additional information, and USB and RS232 connectivity for easy communication.
• Applications
Basic Weighing, Parts Counting, Percent Weighing, Animal Weighing, Density Determination
• Display
Backlit Liquid Crystal Display (LCD); Second line display for additional information or guidance (dot matrix)
• Operation
AC adapter (included)
• Communication
RS232 and USB device (included); GLP/GMP data output with real-time clock
• Construction
Metal base, plastic top housing, removable stainless steel pan, glass draftshield, integrated weigh-below-hook, security bracket, calibration lock and in-use cover
• Design Features
User-selectable environmental filters and brightness settings, auto-tare, auto-dim, user-selectable span calibration points, software lockout and reset menu, userselectable communication settings and data print options, user-definable project and user IDs, software overload/underload indicator, stability indicator, four operating languages
%
Stakpure OmniaTap 12 ultra pure water system
For H2O pure types ASTM I + II.
OmniaTap is the ideal system when both pure water and ultrapure water are required, but in relatively small amounts. The ability to provide both types from a single system results from the combination of ultramodern purification technologies. These also make it possible to connect the system directly to a drinking water tap. A press on the dispenser button activates dispensing of ultrapure water type ASTM I via the digital dispenser control. The recirculation of the pure water held in the installed 10 litre tank keeps it permanently at type ASTM II quality. The pure water tank has a second outlet for feeding downstream end users.
Features
• OptiFill dispenser is standard
• TapWater set for direct connection to a drinking water tap
• 10-litre pure water tank has a pressure outlet
• Tank volume display in percent
• Simple and economical filter replacement
• Leakage sensor is standard
• Ready-to-use, including filter cartridges
%
Julabo PRESTO W50t Highly dynamic temperature control system
Advanced control technology and a small bath fluid reservoir enable highly dynamic temperature control systems to achieve rapid heat-up and cool-down. This gives you the ability to handle difficult temperature challenges quickly.
The PRESTO® systems are designed for precise temperature control as well as rapid temperature changes, making them ideal for reactor vessels, material stress tests, or temperature simulations. These instruments cover a working temperature of -92 to +250 °C with high cooling and heating capacity.
• USB connection
• For highly precise, external temperature applications
• Rapid heating and cooling
• Wide working temperature ranges without changing fluids
• Highest performance with small footprint
• Space-saving design optimizes space utilization in your lab
• Ethernet interface
• SD-Card slot
• RS232 / RS485 (optional) / Profibus DP (optional)
• Connections for alarm-output, Pt100 external sensor and standby-input
• Removable ventilation grid
• Highly precise ICC cascade temperature control
• Electronic level indication
• Integrated programmer
• Unsurpassed power and efficiency
• Space optimized design creates more room directly next to the units
• External Pt100 sensor connection
%
Miele A 101 upper basket
Height adjustable, for the optimum loading of inserts.
• Area of application: reprocessing laboratory glassware and different utensils
• Vertical clearance 160 +/- 30 mm, width 475 mm, depth 443 mm
• With integrated spray arm
• Material: stainless steel

Machine affiliation:
PG 8063
PLW 8636 [LAB / LAB MON]
PG 8562
PG 8582
PG 8582 CD
PG 8504
PG 8583
PG 8583 CD
PG 8592
PG 8593
PLW 8604
PLW 8683
PLW 8683 CD
PLW 8693
PLW 8683 [Safety]
PLW 8693 [Safety]
PWD 8682
PWD 8682 CD
PWD 8692
%
Miele A 102 upper basket
Height adjustable, for the optimum loading of inserts.
• Area of application: reprocessing laboratory glassware
• Vertical clearance 205 +/- 30 mm, width 475 mm, depth 443 mm
• With integrated spray arm

Machine affiliation:
PLW 8636 [LAB / LAB MON]
PG 8562
PG 8582
PG 8582 CD
PG 8504
PG 8583
PG 8583 CD
PG 8592
PG 8593
PLW 8604
PLW 8683
PLW 8683 CD
PLW 8693
PLW 8683 [Safety]
PLW 8693 [Safety]
PWD 8682
PWD 8682 CD
PWD 8692
%
Miele A 103 upper basket
For the optimum loading of inserts.
• Area of application: reprocessing laboratory glassware, mesh trays and different utensils
• Vertical clearance: 95 mm, width 505 mm, depth 472 mm
• Particularly suitable for the reprocessing of DIN mesh trays
• Also suitable for further applications with low height items
• With integrated spray arm

Machine affiliation:
PLW 8636 [LAB / LAB MON]
PG 8562
PG 8582
PG 8582 CD
PG 8504
PG 8583
PG 8583 CD
PG 8592
PG 8593
PLW 8604
PLW 8683
PLW 8683 CD
PLW 8693
PLW 8683 [Safety]
PLW 8693 [Safety]
PWD 8682
PWD 8682 CD
PWD 8692
%
Miele A 150 lower basket
For the optimum loading of injector modules or inserts.
• Area of application: reprocessing pipettes/vials, laboratory glassware, butyrometers, measuring cylinders
• Lower basket with two module connections
• for holding up to 2 injector modules or inserts
• Automatic closing of the connections when not in use
• Clearances: width 494, length 440 mm

Machine affiliation:
PLW 8636 [LAB / LAB MON]
PG 8504
PG 8583
PG 8583 CD
PG 8593
PLW 8604
PLW 8683
PLW 8683 CD
PLW 8693
%
Nabertherm L 15/13/B510 muffle furnace with brick insulation
Heating elements on support tubes radiating freely into the furnace chamber provide for particularly short heating times for these muffle furnaces. Thanks to their robust lightweight refractory brick insulation, they can reach a maximum working temperature of 1300 °C. These muffle furnaces thus represent an interesting alternative to the familiar L(T) ../12 models, when you need a higher application temperature.

Standard Equipment
• Heating from two sides
• Heating elements on support tubes ensure free heat radiation and a long service life
• Multi-layer insulation with robust lightweight refractory bricks in the furnace chamber
• Dual shell ventilated housing made of textured stainless steel sheets for low surface temperature and high stability
• With flap door (L)
• Adjustable air inlet in the furnace door
• Exhaust air outlet in rear wall of furnace
• Solid state relays provide for lownoise operation
• Controller with touch operation B510 (5 programs with each 4 segments)

Option
• Chimney, chimney with fan or catalytic converter
• Over-temperature limiter with adjustable cutout temperature as temperature limiter to protect the furnace and load
• Protective gas connection to purge with non-flammable process gases (not available in combination with chimney, chimney with fan or catalytic converter) not gas tight
• Manual or automatic gas supply system
• Port for thermocouple in the rear wall or in the furnace door
%
Nabertherm LT 5/11/C550 muffle furnace
The muffle furnaces L 3/11 - LT 60/12 have been proven for daily laboratory use. These models stand out for their excellent workmanship, advanced and attractive design, and high level of reliability.

Standard Equipment
• Heating from two sides by ceramic heating plates (heating from three sides for muffle furnaces L 24/11 - LT 60/12) for an optimal temperature uniformity
• Temperature uniformity of +/− 5 K with closed fresh-air inlet in empty work space according to DIN 17052-1 at working temperatures above 800 °C
• Thermocouple type N (1100 °C)
• Ceramic heating plates with integral heating element which is safeguarded and easy to replace
• With lift door (LT)
• Dual shell ventilated housing made of textured stainless steel sheets for low surface temperature and high stability
• Exclusive use of insulation materials without categorization according to EC Regulation No 1272/2008 (CLP). This explicitly means that alumino silicate wool, also known as “refractory ceramic fiber” (RCF), which is classified and possibly carcinogenic, is not used.
• Adjustable air inlet integrated in door (see illustration)
• Exhaust air outlet in rear wall of furnace
• Controller with touch operation C550
• Solid state relays provide for lownoise operation

Option
• Chimney, chimney with fan or catalytic converter (not for L 1 and L 15)
• Over-temperature limiter with adjustable cutout temperature as temperature limiter to protect the furnace and load
• Protective gas connection to purge with non-flammable process gases (not available in combination with chimney, chimney with fan or catalytic converter) not gas tight
• Manual or automatic gas supply system
• Port for thermocouple in the rear wall or in the furnace door