All products

The specialist for H2O pure type ASTM I

The OmniaPure-ST xs basic UV is the one stop solution to produce ultrapure water fulfilling highest demands of analytical and life sciences laboratories if no local water source is available for direct feedwater connection. The integrated feedwater tank for demineralized water allows a mobile production of ultrapure water even in remote locations.
The standardly integrated OptiFill dispenser is a jack-of-all-trades. It is so ergonomically shaped that it enables one-handed use, not only for system operation but also for the monitoring of all quality parameters.
Retractable and pivotable with a flexible connection for the most comfortable supply of ultrapure water to any vessel.

Features

• Reliable ASTM I ultrapure water quality
• The standardly supplied OptiFill dispenser
o enables one handed dispenser operation
o is detachable and ergonomically shaped
o can be turned and is height adjustable
• Integrated 7 l demineralized feedwater storage tank
• Spent filters are simply and quickly exchanged
• Very space saving – fits almost on an A4 sheet
• Clear view of controls with graphic display
• Leak sensor is standard
• Ready to use, including filter cartridge

Standard system components

• Compact housing with easily accessible operating and service hood that enables simple replacement of spent materials in a few seconds
• Build in feedwater tank with 7l volume for demineralized water storage
• Wide-range power supply unit with automatic voltage adjustment to 48 V that can be internationally used
• Quiet running long-life recirculation pump (< 40dB) for complete recirculation through all parts that contact media right up to the tip of the dispenser
• UV-unit with 185/254 nm wavelength for highest microbial cleanliness and TOC-reduction
• Ultrapure purification set for removal of inorganic substances and residual inorganic ions
• Quality rinse rinsing valve for complete disinfection of all parts that contact media as well as quality rinses in interval mode
• Multi-language microprocessor for the control and monitoring of all operating and performance parameters
• Dispenser with adapted microfiltration for sterile ultrapure water dispensing at the point-of-use

The specialist for H2O pure type ASTM I

The OmniaPure-ST xs basic is the one stop solution to produce ultrapure water fulfilling highest demands of analytical and life sciences laboratories if no local water source is available for direct feedwater connection. The integrated feedwater tank for demineralized water allows a mobile production of ultrapure water even in remote locations.
The standardly integrated OptiFill dispenser is a jack-of-all-trades. It is so ergonomically shaped that it enables one-handed use, not only for system operation but also for the monitoring of all quality parameters.
Retractable and pivotable with a flexible connection for the most comfortable supply of ultrapure water to any vessel.

Features

• Reliable ASTM I ultrapure water quality
• The standardly supplied OptiFill dispenser
o enables one handed dispenser operation
o is detachable and ergonomically shaped
o can be turned and is height adjustable
• Integrated 7 l demineralized feedwater storage tank
• Spent filters are simply and quickly exchanged
• Very space saving – fits almost on an A4 sheet
• Clear view of controls with graphic display
• Leak sensor is standard
• Ready to use, including filter cartridge

Standard system components

• Compact housing with easily accessible operating and service hood that enables simple replacement of spent materials in a few seconds
• Build in feedwater tank with 7l volume for demineralized water storage
• Wide-range power supply unit with automatic voltage adjustment to 48 V that can be internationally used
• Quiet running long-life recirculation pump (< 40dB) for complete recirculation through all parts that contact media right up to the tip of the dispenser
• Ultrapure purification set for removal of inorganic substances and residual inorganic ions
• Quality rinse rinsing valve for complete disinfection of all parts that contact media as well as quality rinses in interval mode
• Multi-language microprocessor for the control and monitoring of all operating and performance parameters
• Dispenser with adapted microfiltration for sterile ultrapure water dispensing at the point-of-use

RO-ED ready pure water systems with ED cell, tank and pressure pump
The ready-to-connect pure water system from stakpure combines all treatment steps in one compact and low-noise unit. Pre-treatment, reverse osmosis, electro-deionisation for residual desalination, pure water tank and pressure boosting are integrated in a control cabinet to save space and are completely pre-assembled. Pure water units of the RO ED READY "to use" series produce pure water according to all common standards such as ASTM and DIN 285 + DIN EN 15883 and aqua purificata. Specially developed for the safe and economical supply of pure water to complete laboratory floors and AEMP's in medical practices and hospitals, as well as manufacturing plants in the food and pharmaceutical industries (aqua purificata for external parts cleaning), where space is still a scarce commodity. The clean water system is completed with a digital microprocessor control for display and control of all operating and performance parameters.

Design and scope of delivery
• Electronics control cabinet with transparent door to accommodate all system components
• Pre-treatment unit to protect against free chlorine and particles in the feed water
• Softening unit to protect against limescale and blockage
• Reverse osmosis unit for desalination and removal of removal of organic and inorganic impurities
• Electro-deionisation module for residual desalination Continuously self-regenerating - without chemicals
• Pure water tank incl. level control for automatic storage of the produced pure water
•Pressure boosting system incl. pressure control for low-noise low-noise delivery of the pure water to the end user
•Multilingual microprocessor control with LCD display for control and monitoring of RO systems. Display of Permeate conductivity, fully automatic flushing cycles and potential-free fault indication.

System structure softening plant
Volume-controlled system, for softening iron- and manganese-free drinking water, according to drinking water regulations, fully automatic, 5-step central control valve type FLECK 5600 SXT with microprocessor made of NORYL with integrated blending valve and water meter. Pressure tank made of corrosion-resistant GRP, incl. cation exchanger of highest quality, installed in cabinet tank with float valve
• Type: WEA 32 Compact
• Capacity: 32 m³x°dH
• Nominal flow rate: 0.32 m³/h
• Resin quantity: 8 litres
• Salt supply: 25kg
• Salt consumption: approx. 1.92 kg/reg.
• Water consumption: 0.08 m³/reg.
• Operating pressure: 2 to 6 bar
• Water temperature: max. 30°C
• Ambient temperature: max. 5 to 40°C
• Electrical connection: 220 V 50 Hz
• Dimensions of housing (WxDxH) 310 x 430 x 660 mm
• Connection: R1

System design Reverse Osmosis Unit
• Safety pressure switch for shutting off when feed water pressure is too low
• High-pressure pump for generating the working pressure
• Reverse osmosis membrane incl. pressure pipe and all necessary fittings
• Working pressure manometer for system monitoring and fault diagnosis
• 2 x solenoid valves for raw water and quality flushing
• 2 x regulating valves for setting the working pressure and the WCF rate
• Measuring cells for determining the raw and clean water conductivity values
• Complete piping made of PA, PP, POM and stainless steel materials

Structure electro-deionisation
• Electro-deionisation module
• Flow meter for pure water, concentrate and electrode rinse water
• Set of regulating valves
• Conductivity measuring cell
• Complete piping in PA, PP, POM and stainless steel
• Microprocessor control with LCD display for control and display of all operating and performance parameters.

Digital microprocessor control
Universally applicable for the automatic control and monitoring of reverse osmosis systems. The controller is equipped with one or optionally two conductivity meters with temperature compensation. Optional board for recorder outputs 4-20mA possible. Integrated in a separate electronic control cabinet for wall mounting. The following functions/operating modes are executed and displayed:
• Stand-by
• Production
• Rinse after production
• Flushing interval
• Maintenance
Adaptable options through programmable configuration that can be stored in a memory.

Properties
Menu-guided programming in the 2-line display
• Language selection for English, French, Spanish, Italian or Dutch
• Adaptation to user-specific requirements through programmable options
• Easy handling and control through the use of symbols on the control buttons
• Universally applicable even for larger reverse osmosis systems
• Production can be controlled via manual or level switch
• Maintenance interval display programmable via code
• Service number can be shown in the display
• Status display can be called up via info key for the following conditions: Current status for inputs and outputs, service telephone number, software version, programming status, type of fault messages, Interval rinsing with current time interval, manual rinsing with time specification, conductivity measuring probe, cell constants
• Display of the current permeate and pure water conductivity with indication of the desalination rate in a large green LED display.
• Connection of optional board for recorder outputs 4-20mA
• Inputs for : Production stop, storage tank full/empty, overpressure, raw water shortage, motor protection switch, alarm reset, temperature sensor (optional), concentrate monitor
• Integrated conductivity meter with measuring range switchover
• Cell constants adjustable from for measurement of conductivities 0.1- 100000μS/cm
• Cell constants programmable from 0.01-10.00cm
• Manual and automatic temperature compensation
• Extension of conductivity measurement by dual function display
• Thermoswitch for pressure pump with fault signal available as option
• Outputs for : Pressure pump (contactor), input solenoid valve, flush valve, permeate valve, fault signal contact
• Insensitive to mains failures, as all programme functions are stored without battery.
• Large microprocessor memory capacity with "watchdog" against illegal "Operation Code and frequency monitoring
• Manufacture of the control unit in compliance with the EMC standard by means of galvanic isolation between microprocessor and input and output circuits, plus extra built-in filter
• Available input/output voltages (input/output) 24/24V 115/115V 230/230V

System design pure water tank
Storage tanks made of black PE for storing pure water from reverse osmosis systems. Closed and opaque design, angular, incl. 200 mm manhole for cleaning. The tank is completely piped and available with optional additional equipment. Incl. level control with min./max. control for fully automatic storage.
Scope of delivery:
• CO2 absorber, tank ventilation and sterile overflow
o Nominal volume: approx. 200 litres
o Material: PE black
o Inlet and overflow connection: R ¾".
o Connection outlet: R 1 ¼"

System design Pressure boosting
The PST 2500 PC pump station is a self-priming, horizontal, single-stage centrifugal pump with built-in ejector. The squirrel-cage motor and the use of a mechanical shaft seal make the unit maintenance-free and insensitive to faults. Long service life due to the use of stainless steel for all highly stressed parts, such as impeller and housing. In combination with the automatic pressure control, the unit becomes a complete supply station.
Single stage centrifugal pump
Automatic pressure control
• Type: PST 2500 PC
• Pumping medium: water
• Actual flow rate 3.4 m³/h
• At actual delivery head: 22 m
• Switch-on pressure Pressure control: 2.2 bar
• Material impeller and casing: stainless steel AISI 304
• Ambient temperature: max. 40°C
• Electrical connection: 230 V / 50 Hz
• Power consumption 850 W
• Dimensions incl. pressure control approx. W 206 x D 364 x H 500 mm
• Connection inlet d25 grommet
• Connection outlet R ¾"
• Order no. 16551200

Technical data
for connection to softened or hardness-stabilised drinking water in accordance with the German Drinking Water Ordinance.
• Blocking index: max. 3
• Salt content: max. 2,000 mg/l
• Chlorine concentration: < 0.01 mg/l
• Manganese content: < 0.05 mg/l
• Iron content: < 0.05 mg/l
• CO2 content: max. 15 mg/l
• SiO2 content: max. 0.4 mg/l
• pH range: 4 to 11

Pure water values
• RO capacity ( at 10°C ): 100 l/h
• RO membrane retention rate: > 99 % salts, germs and bacteria
• WCF rate adjustable up to 75
• Output EDI ( at 10°C ): 50-80 l/h
• Membrane retention rate RO: > 99 % salts, germs and bacteria
• Residual conductivity ED: 0.06 to 1 μS/cm*
• Type. Residual conductivity ED: 0.1 μS/cm*
• TOC value ED: < 30 ppb
• Silicate and germ reduction ED: > 99 %*
• WCF rate RO/ED adjustable: up to 75/90

Connection values
• Ambient temperature: 5 - 40°C
• Water temperature: 5 - 35°C
• Raw water pressure RO: 2 to 6 bar
• Working pressure RO: max. 14 bar
• Working pressure ED: 1 to 4 bar
• Clean water back pressure: max. 0 to 1 bar
• Supply voltage: 230 volts / 50 Hz
• Connected load: 1.5 kW
• Connection inlet:DN 20
• Connection outlet: DN 20
• Brine connection: DN 10
• Dimensions (WxDxH): 1020 x 600 x 1850 mm
• Weight approx.: 270 kg
• Order no. 17600080

The compact for H2O pure type ASTM II + DIN 285
RO ED ready mini is the system of choice when pure water is needed for the complete laboratory supply and space is limited. The system meets international water standards such as ASTM, ISO 3696, CLSI, DIN 285 and is economically maximised by the combination with the continuously self-regenerating electro-deionisation. In addition, the system holds 50 litres of pure water in a 50l storage tank with optional recirculation module for withdrawal. A frequency-controlled pressure and ring line pump can be used to supply downstream end devices and/or ring line systems. Mobile on castors, the system can be
integrated in a 90 cm laboratory base cabinet to save space. The RO ED ready mini system is predestined for the supply of autoclaves or dishwashers and ultrapure water systems in laboratory and medical technology.
Features
• All-in-one unit - completely pre-rolled and ready for connection
• Space-saving integration in a 90' base cabinet
• Economical ultrapure water quality ASTM II + DIN 285
• Continuous residual desalination by means of electro-deionisation
• 50 l pure water tank with optional recirculation module
• Clear control with graphic display
• Leakage sensor as standard
• Frequency-controlled pressure and ring line pump

System design - as standard
• Mobile T-frame on castors to accommodate all system components made of PE. With drip tray over the entire surface - accumulation edge 4 cm.
• Pre-treatment unit - pore size 5 μm with activated carbon to protect the membranes from particles and chlorine
• Wide range power supply with automatic voltage adjustment to 48 V enables international use with only one power supply
• Low-noise LongLife RO pressure pump (< 40dB) with automatic rinsing cycle to flush deposits from the membranes.
• HighPerformance reverse osmosis modules for the retention of inorganic and organic ingredients - extremely powerful
• Electro-deionisation module for continuous and economical resin regeneration without the addition of chemicals
• Pure water tank with a volume of 50 l made of black PE and conical bottom drain for complete emptying of residues
• CO2 absorber, sterile tank ventilation filter and sterile tank overflow protect against contamination by airborne germs and carbon dioxide
• Quality flushing valve for complete disinfection of all parts in contact with the media as well as quality flushing in interval mode
• Multilingual menu navigation for controlling and monitoring all operating and performance parameters as graphic display
• Frequency-controlled pressure and ring line pump with pressure sensor, switch box, 2 l pressure compensation vessel for supplying downstream terminal devices - 1 m³h/ at 4 bar

Optionally available:
• Recirculation module for complete tank recirculation and connection of external ring line systems - consisting of solenoid valve, timer and pressure maintenance
• UV disinfection unit as immersion tube system for the clean water tank Output 16 W, wavelength 254 nm, with ballast unit

Microprocessor control
• Multilingual microprocessor control with graphic display and colour change green/red on error message
• Individual setting options for conductivity display in MΩxcm or μS/cm as well as language switchover German/English
• Multi-stage conductivity & temperature monitoring for permeate & pure water, temperature-compensated with infinitely variable limit value setting
• USP-compliant and highly precise thanks to automatic adjustment before each measurement with integrated reference resistor and temperature compensation that can be switched off
• Continuous monitoring of the UV unit and leakage monitoring with error display and automatic safety shutdown of the water supply

Feed water requirements
softened drinking water according to DIN 2000
• Feed water temperature: +2°C to 35
• Feed water pressure: 2 to 6 bar
• Manganese and iron content: < 0.05 mg/l
• Chlorine content: < 0.1 mg/l
• Blocking index (SDI): max. 3

Pure water values type II
• Pure water conductivity*: 10-1 MΩxcm - 0.1 - 1 μS/cm
• Silicate retention* : > 99
• Pure water output at 15°C: 20 l/h
• Typical applications: Laboratory water supply type II / DIN 285; Supply of autoclaves and laboratory dishwashers
*in dependence of feed water quality and CO2

Technical data
• Ambient temperature: +2 to 35°C
• Supply voltage: 230 Volt / 50-60 Hz
• Total connected load: 1.1 kW
• Connection size: R ¾"
• Dimensions (WxDxH): 800 x 600 x 800 mm

Work space in laboratories must be used efficiently. The Omnia xs system frees up space on the lab bench and makes work more efficient.
Despite the extremely compact design in xs format, the system works in a resource-saving and completely autonomous way. Accessories such as a leakage sensor, pressure reducer, and pre-treatment cartridges are already integrated in the compact housing. This saves space in the laboratory and also ensures exceptional operational and occupational safety.
OmniaTap xs basic is the ideal system when both pure water and ultrapure water are required, but in relatively small amounts. The ability to provide both types from a single system results from the combination of ultramodern purification technologies. These also make it possible to connect the system directly to tap water. A press on the dispenser button activates dispensing of ultrapure water type I via the digital dispenser control. The recirculation of the pure water held in the installed 7 litre tank keeps it permanently at type II quality. The pure water tank provides a second optional outlet for feeding downstream end users.
Features
• OptiFill basic dispenser is standard
• Spent filters are simply and quickly exchanged
• Leakage sensor is standard
• Ready-to-use, including filter cartridges

Pure and ultrapure water from the super slim Omnia xs compact system with intuitive basic dispenser.
Work space in laboratories must be used efficiently. The Omnia xs system frees up space on the lab bench and makes work more efficient.
Despite the extremely compact design in xs format, the system works in a resource-saving and completely autonomous way. Accessories such as a leakage sensor, pressure reducer, and pre-treatment cartridges are already integrated in the compact housing. This saves space in the laboratory and also ensures exceptional operational and occupational safety.
When your need is for highest quality pure water that fulfils the demands of analytical and life science laboratory requirements, then one of these OmniaPure systems will be the right choice for you. The incorporated pre-treatment constantly ensures the reliability of your experimental results and reduces running costs.
Features
• OptiFill basic dispenser is standard
• Spent filters are simply and quickly exchanged
• Leakage sensor is standard
• Integrated pressure reducer is standard
• Very space saving
• Ready-to-use, including filter cartridges

Storage tanks in grey PP for storing purified water from reverse osmosis systems. Closed and opaque design, round, including manhole for cleaning. The tank comes completely piped and is available with optional accessories.
• Input connection: R ¾''
• Drain connection: R 1¼''
• Volume (l): 100
• Dimensions (Ø x height, mm): 470 x 680
• Net weight (kg): 12

Completely automatic water softening unit with Mix Multi filter material, for softening of iron and manganic free drinking water and removal of organics, for bad water qualities and well water application that produces softened water with a residual hardness of 0.1° dH by means of the neutral exchange process with strong acid cation exchanger. Common salt is used for regeneration. Regeneration is carried out volume-dependently. Manual initiation of regeneration is also possible.
Scope of delivery:
• Fiberglass pressure tank and filling with cation exchanger
• Central control valve with 5 step regeneration program
• Container for dissolving salt
• Pre-assembled system ready for connection
Technical data:
• Capacity: (at 10°dH - tap water) 32 m³x°dH
• Flow rate: 0,32 m³/h
• Resin volume: 8 liter
• Capacity of salt container: 25 kg
• Salt consumption: 1,92 kg/reg.
• Water consumption: 0,08 m³/reg.
• Operating pressure: 2 to 6 bar
• Max. water temperature: 30°C
• Max. ambient temperature: 5 to 40°C
• Power supply: 220 V 50 Hz
• Dimensions: W 310 x D 430 x H 660 mm
• Piping connections: R1“

One way mixed bed ion exchange resin for polishing process water to achieve demineralized water quality.

Stakpure DS ion exchange cartridge - stainless-steel, pressure-resistant to 10 bar
For any situation requiring up to 300 litres of demineralised water an hour. A sophisticated flow system for incoming water ensures a fast and effective flow of water through the mixed-bed system with ion-exchange resins.
• Flow rate: 300 l/h
• Capacity for 10° total dissolved solids: 1500 l
• Pure water quality: 0,1 - 20 μS/cm
• Max. water temperature: 30 °C
• Material: stainless steel – AISI 316
• Dimensions mm (Ø x height): 240 x 410
• Connection: R ¾ "
• Weight, approx.: 14 kg

Work space in laboratories must be used efficiently. The Omnia xs system frees up space on the lab bench and makes work more efficient.
Despite the extremely compact design in xs format, the system works in a resource-saving and completely autonomous way. Accessories such as a leakage sensor, pressure reducer, and pre-treatment cartridges are already integrated in the compact housing. This saves space in the laboratory and also ensures exceptional operational and occupational safety.
OmniaTap xs basic is the ideal system when both pure water and ultrapure water are required, but in relatively small amounts. The ability to provide both types from a single system results from the combination of ultramodern purification technologies. These also make it possible to connect the system directly to tap water. A press on the dispenser button activates dispensing of ultrapure water type I via the digital dispenser control. The recirculation of the pure water held in the installed 7 litre tank keeps it permanently at type II quality. The pure water tank provides a second optional outlet for feeding downstream end users.
Features
• OptiFill basic dispenser is standard
• Spent filters are simply and quickly exchanged
• Leakage sensor is standard
• Ready-to-use, including filter cartridges

Pure and ultrapure water from the super slim Omnia xs compact system with intuitive basic dispenser.
Work space in laboratories must be used efficiently. The Omnia xs system frees up space on the lab bench and makes work more efficient.
Despite the extremely compact design in xs format, the system works in a resource-saving and completely autonomous way. Accessories such as a leakage sensor, pressure reducer, and pre-treatment cartridges are already integrated in the compact housing. This saves space in the laboratory and also ensures exceptional operational and occupational safety.
When your need is for highest quality pure water that fulfils the demands of analytical and life science laboratory requirements, then one of these OmniaPure systems will be the right choice for you. The incorporated pre-treatment constantly ensures the reliability of your experimental results and reduces running costs.
Features
• OptiFill basic dispenser is standard
• Spent filters are simply and quickly exchanged
• Leakage sensor is standard
• Integrated pressure reducer is standard
• Very space saving
• Ready-to-use, including filter cartridges

Storage tanks in grey PP for storing purified water from reverse osmosis systems. Closed and opaque design, round, including manhole for cleaning. The tank comes completely piped and is available with optional accessories.
• Input connection: R ¾''
• Drain connection: R 1¼''
• Volume (l): 200
• Dimensions (Ø x height, mm): 560 x 840
• Net weight (kg): 14

One way mixed bed ion exchange resin for polishing process water to achieve demineralized water quality.

Up to 10 bar pressure-resistant, stainless steel, empty cartridge for ion exchange resin.
• Material: stainless steel – AISI 316
• Dimensions mm (Ø x height): 240 x 410
• Connection: R ¾ "

One way mixed bed ion exchange resin for polishing process water to achieve demineralized water quality.

Work space in laboratories must be used efficiently.
The Omnia xs system frees up space on the lab bench and makes work more efficient. Despite the extremely compact design in xs format, the system is exemplary in its resource-saving and completely autonomous operation. Accessories such as a leakage sensor, pressure reducer, and pre-treatment cartridges are already integrated in the compact housing. This saves space in the laboratory and also ensures exceptional operational and work safety.
OmniaTap xs touch is the ideal system when both pure water and ultrapure water are required, but in relatively small amounts. The ability to provide both types from a single system results from the combination of ultramodern purification technologies. These also make it possible to connect the system directly to tap water. A press on the dispenser button activates dispensing of ultrapure water type I via the digital dispenser control. The recirculation of the pure water held in the installed 7 litre tank keeps it permanently at type II quality. The pure water tank provides a second outlet for feeding downstream end users.
Features
• OptiFill touch dispenser is standard
• Spent filters are simply and quickly exchanged
• Leakage sensor is standard
• Integrated pressure reducer is standard
• Precise volume control
• Ready-to-use, including filter cartridges

Space-saving. Flexible. Intuitive. Resource-saving.
Work space in laboratories must be used efficiently.
The Omnia xs system frees up space on the lab bench and makes work more efficient.
Despite the extremely compact design in xs format, the system is exemplary in its resource-saving and completely autonomous operation.
Accessories such as a leakage sensor, pressure reducer, and pre-treatment cartridges are already integrated in the compact housing. This saves space in the laboratory and also ensures exceptional operational and work safety.
When your need is for highest quality pure water that fulfils the demands of analytical and life science laboratory requirements, then one of these OmniaPure systems will be the right choice for you.
The incorporated pre-treatment constantly ensures the reliability of your experimental results and reduces running costs.

Features:
• OptiFill touch dispenser is standard
• Spent filters are simply and quickly exchanged
• Leakage sensor is standard
• Integrated pressure reducer is standard
• Resource-saving filter volume
• Very space saving
• Ready-to-use, including filter cartridges

Technical data:
• Ambient temperature [°C]: + 2 up to 35
• Printer port: RS232
• Data port: USB-A
• Feedwater connection: R3/4″

Storage tanks in grey PP for storing purified water from reverse osmosis systems. Closed and opaque design, round, including manhole for cleaning. The tank comes completely piped and is available with optional accessories.
• Input connection: R ¾''
• Drain connection: R 1¼''
• Volume (l): 300
• Dimensions (Ø x height, mm): 690 x 830
• Net weight (kg): 16

One way mixed bed ion exchange resin for polishing process water to achieve demineralized water quality.